@pfile wrote:
tomorrow morning i'll post the full log, but i saw that problem again:
[06/22/17 21:33:28.291][DEBUG] [Sequence Thread] Alnitak Flat Box - Setting Brightness to 16 [06/22/17 21:33:28.291][DEBUG] [Sequence Thread] EventMarker 2 - t:m101 flats (18); e:1; f:20; o: [06/22/17 21:33:28.291][DEBUG] [Sequence Thread] EventMarker 3 - t:m101 flats (18); e:1; f:20; o: [06/22/17 21:33:28.291][DEBUG] [Sequence Thread] EventMarker 4 - t:m101 flats (18); e:1; f:20; o: [06/22/17 21:33:28.291][DEBUG] [Sequence Thread] Setting filter position 2... [06/22/17 21:33:28.303][DEBUG] [Sequence Thread] Setting filter: G... [06/22/17 21:33:28.303][DEBUG] [Sequence Thread] Moving filter wheel, isMoving, check 1... [06/22/17 21:33:28.303][DEBUG] [Sequence Thread] Moving filter wheel, isMoving, check 1 is complete... [06/22/17 21:33:28.343][DEBUG] [Sequence Thread] Adjust focuser pos per filter: Moving focsuer to focus position (30761)... [06/22/17 21:33:28.378][DEBUG] [Sequence Thread] Adjust focuser pos per filter [06/22/17 21:33:28.378][DEBUG] [Sequence Thread] Old filter: R; Focus pos: 30756 [06/22/17 21:33:28.378][DEBUG] [Sequence Thread] New filter: G; Focus pos: 30761 [06/22/17 21:33:28.378][DEBUG] [Sequence Thread] Pos delta: 5 steps [06/22/17 21:33:28.378][DEBUG] [Sequence Thread] New position-> (current: 59791) + (delta: 5) = 59796 [06/22/17 21:33:28.382][DEBUG] [Sequence Thread] Focuser moving to 59796 [06/22/17 21:33:28.386][DEBUG] [Main Thread] Alnitak Flat Box - Turning Light On [06/22/17 21:33:28.409][DEBUG] [Sequence Thread] Focuser backlash active, modified move to 59816 [06/22/17 21:33:28.455][DEBUG] [Sequence Thread] Focuser move call complete [06/22/17 21:33:28.460][DEBUG] [Focuser Backlash Thread] Focuser backlash thread has started... [06/22/17 21:33:29.519][DEBUG] [Focuser Backlash Thread] Backlash thread has detected that movement to modified position (59816) is complete... [06/22/17 21:33:29.519][DEBUG] [Focuser Backlash Thread] Moving focuser to original requested position (59796)... [06/22/17 21:33:29.519][DEBUG] [Focuser Backlash Thread] Focuser backlash compensation needed. Steps: 20 Direction:IN [06/22/17 21:33:29.519][DEBUG] [Focuser Backlash Thread] Focuser moving to 59796 [06/22/17 21:33:29.577][DEBUG] [Focuser Backlash Thread] Focuser move call complete [06/22/17 21:33:29.972][DEBUG] [Sequence Thread] Focuser position matches requested position (59796), continuing... [06/22/17 21:33:29.972][DEBUG] [Sequence Thread] focuser move is complete...prior to this, the focus point was in the ~14k range. to remedy this i've gone into the moonlite driver and set the current position to 30,000 and disconnected and reconnected SGP to the focuser. i guess this would indicate that its actually a problem with the moonlite driver. i have logging turned on there so i will fish out that log as well.
rob
Posts: 2
Participants: 1
